LESSON: A good analyzer makes tuning an antenna fast, simple  and accurate! The AIM 4170 gave us a TON of info (most of it going over my head) and let us see how the C Pole was doing in several areas.  Take a look at this output! (Click on the image for a larger version)

K4UPG C Pole Scan Results

LESSON: I followed Niel’s directions, but did not have a small plastic coffee container so used a Quart Coke bottle instead. So I call it a Coke Choke and it seems to work well. Here’s a photo to show it off!

Coke Choke Ready for Duty

I think this one is a keeper. Goes up easily, hears well and loads nicely too. I made a few brief contacts and called it a day, but look forward to more C Pole action in the days ahead.

72,

Kelly K4UPG PB #173

p.s. Don’t forget to vote in the Ideal Ham Radio QTH poll on the blog!

Doggone noise and weak band conditions ruined the day so I decided to experiment with the new C Pole antenna that  Neil W0VLZ had suggested. To get rid of a hunk of fiberglass gel inside the barrel of one of the Black Widow Crappie poles I used my cheapo Harbor Freight rotary tool which is a lame imitation of a Dremel tool but gets the job done. A few minutes of fitting and I was good to go.

I’m pretty impressed with it though conditions did not allow for any QSO’s yet. I cut the wire a bit longer than Niel’s directions but it tuned up 1:1 at 13.889 on my MFJ 207 Analyzer. At 14.060 it was a bit over 1.4:1 which is plenty usable. Next time out I’ll do a bit of trimming and be right on the money! Compared to the EFHW in a 20 ft L configuration, it did seem a bit noisier but with condx so difficult it would be hard to tell without some instrumentation.

LESSON: The C Pole is a pretty fine design. I need to work on the physical setup to improve the way the antenna hangs. The crappie poles I used were a bit too flimsy on the top section and leaned inward from the weight of the wire. A better tippy top support system is needed.

LESSON: Niel’s C Pole base design and specs worked very well.  Lacking an empty plastic coffee can, I used a quart diet soda bottle of the same dimension and it worked very well for the balun section. With winds of approximately 15 mph and gusts to 20+ the antenna was stable and I did not use the spikes for the outriggers that I had prepared. Great work Niel. The weight of the base makes it a good choice for backyard or campground use.

LESSON: The C Pole would be a fantastic portable antenna sans the earth side supports. Chuck Carpenter W5USJ has posted a picture of this configuration. Take a look. One point hanger  and spreaders at the top and bottom and simple stake to the ground for anchoring it and you are good to go. I will be testing this next time out by the lake. Winner!

LESSON: The off center fed dipole folded like this and deployed vertically is a good compact option for antenna restricted hams. I bit more work on the frame and support system may pay good dividends in stability and efficiency.

Hope to fly this new antenna in its tree configuration this weekend. I’ll update my results then.

72,

Kelly K4UPG PB #173

Our monthly Polar Bear QRP Club outing was last weekend, and I hustled to put together a new C Pole antenna using Niel W0VLZ’s description. After gathering all the parts I set about preparing them. With the 100F temperatures and high humidity, that was a chore since I don’t have a garage with my condo and use my back porch as the workshop. I also have a less than full set of tools and to trim the 3/4 inch PVC pipe to fit the bases of the 16.5 ft Black Widow Crappie poles I had to resort to my Buck knife.

LESSON: Plan ahead and borrow the tools I need!!! YIKES.

I was a bit surprised how heavy the treated 1×4 lumber was. It certainly is not an antenna that is well suited to portable ops where it has to be carried very far.

LESSON: Think about how something is to be used BEFORE using it!

Got the C pole components loaded into the car and transported to the nearby lakeside park in our development. It is a nice quiet spot with towering pine trees and without too many curious visitors, so its a nice QRP portable site. Got my new Coleman shelter set up and went to work on the C Pole. Oops… another lesson. In preparing the PVC to fit into the crappie poles, I only tested the two pvc poles fit into ONE of the two crappie poles. After lugging the framework, antenna wire, coax, balun,  and poles about 100 yds to my site, I discovered crappie pole #2 had a big drop of fiberglass inside the open end of the pole and the PVC would not fit at all.

K4UPG Polar Bear Site Aug 2010

C Pole Aborted Setup by Ninja wannabe K4UPG

LESSON: Check ALL the parts and do a trial setup BEFORE lugging the stuff across the wet grass and wasting time attempting to set it up.

LESSON: Don’t use a new antenna for the first time when the goal is get on the air and have fun!

For the Polar Bears, it was a frustrating weekend for most of us. Propagation was spotty and noise level was as high as the heat. At least I did reconnect with my antenna lovin’ PB friend Aaron, N9SKN/2 working from his hotel parking lot in NJ and had a couple nice ragchews including Julio NP3CW who was 599 and despite two guys calling CQ on top of us was able to be copied well. Great QRP signal Julio.

As you can see, I went ninja and tied a piece of old tee shirt around my head as a sweatband. Actually I was emulating our Alpha Bear, Ron WB3AAL after I read of his early Appalachian Trail exploits and saw a photo of him in his youth and ninja radio mode. Well I tied it TOO TIGHT and left it on TOO LONG and came home with a painful big red stripe on my forehead that lasted for several hours and hurt like all git out.

Ouch Head for the Web... Don't try this at home! Grrrrrrr!

LESSON: Baby Polar Bears should not try to be like the Alpha Bear and wear an unapproved homebrew sweatband. These can be hazardous to one’s health and well being. Don’t try this at home kids!

Beef n Pepper Jack Cheese Wrap K4UPG style

p. s. For our Summer Picnic Events, we are supposed to send a picture of our sammich that we have for lunch. So here is mine!

Until next time…

72,

Kelly K4UPG Polar Bear #173

Grrrrr! The Polar Bears Are On The Loose!

This should be a good weekend for QRP portable. The Polar Bear QRP Group will be out for another Polar Bear Summer Picnic Event and Polar Bears from Spain to the West Coast of the US will be out looking for BSO’s. Grrrrr! I am PB #173 and we’re over 200 members now. With the new Twitter and APRS connections to QRPSPOTS.COM which also point to the excellent spotting site of K3UK with a section for FISTS/QRP Ops to spot and sked one another, there are plenty of ways to use technology to help find each other. Add in a few other contests and state QSO parties, and there should be some buzzing going on this weekend. Makes me wonder when the FOBB results will be announced! Buzzzz Buzzzzz

I’ll be out and if all goes well I will be field testing a new C Pole antenna based on the suggestion I received from Neil W0LVZ. I added some switchable capacitance to my BLT+ and have rewound the main toroid to see if I can push the range a bit more with it so will have a delta loop and probably my W3EDP in the air too. I love playing with antennas and am still amazed when the ones I build actually make contacts!

Give a listen for me on the QRP watering holes on 40m, 30m and 20m Saturday morning. I’ll be self spotting on QRPSPOTS and the K3UK sites to make it easier for you to find me. Let me know how my newest antenna is workin’.

72,

Kelly K4UPG

PB #173

I still think the tin foil does the magic!

After years of neglect, this analog era ham is willing to admit I only understand a bit about digital electronics. (Yep! Pun intended.) Well into the second week of my sabbatical leave, I have begun to plot out a course of study to get up to speed on the state of the art that I have so long neglected. Should be fun. There seems to be a good bit of open source help online these days and I have my trusty ARRL Handbook, Extra Class study guide, Antenna Handbook and assortment of other aids.

Any suggestions from the veteran techies out there will be greatly appreciated.

I am a learn by doing/hands-on sort of guy and find deep theory puts me into a semi-catatonic state after a few minutes.  For me, it’s a whole lot more fun to take a stab at things and find out if they smoke, and it also makes a lot more sense when I can dink and tweak and see what that actually does. But since that is a bit expensive, perhaps I should learn how to use software like spice to do simulations? Any recommendations for how to learn this software?

Another area of toe dipping will be learning to do antenna modeling. For years I’ve looked at those charts and made little sense out of them. HA… I like to throw wire out and see what happens, but in the summer heat, maybe it is wiser to do a bit of modeling from my air conditioned den?

Thanks WX7S-- Your site looks AWESOME for learning this stuff!

I’ll try to share some of the learning curve, but would love to hear from some of you that have gone before. Shortcuts are nice. WX7S your site looks like a great place for me to start! Thanks for the effort it takes to do that.

This weekend (Sat 14 Aug 2010) the Central Florida QRP Group will gather for breakfast at 0730 (Denny’s in Sanford, FL) and off to Sylvan Lake Park in Sanford, FL at 0900 EDT to operate. If you like cw and qrp or are just plain curious… come join us!

As a student of anthropology and culture, I see a bit of a tribal influence among the amateur radio ops of the world. We tend to cluster into tribes based upon our modes of operation and other specialized pursuits like contesting, fox hunting, award seekers, etc. Each tribe has its own special characteristics, culture, jargon and social structure.

What I enjoy most about the QRP tribe is that the Elmer spirit is still very much alive and well. Although we all are a bit competitive and like to think we have a line on the best way to do QRP, there is a healthy amount of sharing of information, expertise and even hardware. Groups like Adventure Radio Society, NAQCC, Flying Pigs, Polar Bears, AZ Scorpions, NE QRP, North Georgia, 4 States, etc breed healthy competition and provide us with sources of information and expert assistance when needed. I sure am enjoying getting to know, both on air and in person, some of the people that make these groups work.

My recent connection with Diz W8DIZ while operating the FOBB, prompted me to go back and read the history of the Flying Pigs and to read through the archives of the Bacon Bits Newsletter. There is real gold and a wealth of interesting info that’s been recorded and made available freely. Other clubs have the same heritage. I say a BIG THANK YOU to all the QRP groups for sharing their experience and stories. It makes me feel proud to be part of the tribe!

What about you? What do you enjoy about QRP? Leave a comment and share your thoughts and story.

Sunday the bands were full of QRP ops, both home based and portable, so the activity really did make a BUZZ despite band conditions that have not been all that helpful to hf qrp contacts.  The weather was HOT, but hey, find some shade, altitude or water and go for it. Historically this is the time of year for this event and as others have commented, it keeps our activity up during the summer time when vacations and mowing the grass take their toll on ham radio activity.

As far as fast cw, I’m not fast (not even close hi hi), but it sure is fun listening to the buzz on the bands rather than QRN and a high noise level with only a few weak signals. Certainly I am not a hard core contester. My cw skills are still in need of practice, but isn’t that what events like this provide? I often have to listen multiple times to get the callsign and info but that repetition and practice pushes my speed and confidence level up every time I try. After listening to a fast op several times I have the info I need and then I jump in and have fun making a contact at speeds faster than my comfort zone. Most of us slow guys can send faster than we can receive, right? Come on in, the water is fine, and FUN!

My XYL, Connie and I drove over to Honeymoon Island State Park on the Gulf Coast in Dunedin, Florida. This is a very pretty beach, not overly crowded most of the time and has been one of the top rated beaches in the US for several years. The weather cooperated, there was no sign of the BP oil spill that has run so many tourists to other locations, and we snagged a primo spot to operate right next to the water.The only negative, if you call it that, was that the view was sometimes distracting, but sure was enjoyable.

K4UPG Distracting View from my FOBB 10 Site

K4UPG Honeymoon Island FOBB Site July 2010

My trusty Sierra and Buddistick provided plenty of action so I never switched over to my mini-bac Delta Loop backup antenna. I also stuck to 20m the whole contest since 40m has been in such poor condition here in Florida lately.

One of the great things about these events is the leveling of the playing field. It is fun to contact the guys that write the articles, create the websites and design the equipment that we use for our hobby. My score was modest at 26 QSO’s, 18 Bumblebees and 17 states and provinces but it was one fantastic day of activity for me! Being able to connect with the big guns of QRP was a thrill too!

W8DIZ Stops By to say Hello to K4UPG

K4UPG search and pounce FOBB 10

For me, one of the highlights was when W8DIZ rode over to meet me as I was setting up my site. Diz lives about 3.5 miles from Honeymoon island and is a regular bicycle visitor of this great beach location. I’ve been a customer of his toroid and kit business and have benefited from the info he has shared, not to mention being one of the movers and shakers of the Famous Flying Pigs QRP group. Diz I was honored that you took time out from a busy family day to swing by and say HI! Thanks for the help getting our screen house up too!

Thanks to Adventure Radio Society and the guys that put this event on for all of us. We appreciate the effort it takes and you deserve the very best of 73′s from all of us.

72,

Kelly K4UPG  BB #10

I’ve been working on that issue for a bit and offered my current solution. Still not 100% perfected, but it is working well now. Here in Florida, the tallest trees are mostly pines and the bark is pretty sticky with sap and lots of crooks and crannies that don’t allow monofilament fishing line to slide as freely as I’d like. I’ve tried the archery reel and slick braided line and although it does slide nicely through the trees, it is much slower and challenging to reel in and also is very prone to tangles and wind knotting which wastes time to untangle. In low wind or super sticky pine trees it is still the best solution.

Below are some photos of my cheapo solution to the slingshot line launcher. A $4 slingshot from Harbor Freight and a 99 cent shelf bracket from Lowe’s are the basic components. One challenge is being able to see where the sinker and line end up after the shot. I tried painting the sinkers, but in tall grass or lots of leafy trees, it did not show up as easily as I would like. The simple solution I found was to use fluorescent plastic surveyor’s tape (also from Lowe’s) to add both vivid color and some motion to help me locate the sinker whether in the trees, air or ground. I’ve also recently switched to red colored monofilament line called Cajun Red Lightning that offers a bit more visibility than clear monofilament.

Here are the basic elements... slingshot, Shelf bracket, spincast reel

If you are looking for an inexpensive simple solution, this might be the answer! Give it a try and let us know how it works for you. Leave a comment or better yet, join the 4 States QRP Group and join the conversation.

Closeup of the mounting of the reel

The assembled launcher -- slingshot taped to bracket

I built an antenna tuner based on AA5TB’s design for an end fed half wave antenna. I am using a 3 ft or so counterpoise on the ground as Steve suggests. On the analyzer in a test lashup it was a bit touchy to hand capacitance but tuned well even up to 21Mhz. Since I am not thinking of backpack size I used a pretty good sized enclosure for it. I am using an air variable 6-160pf cap instead of a polyvaricon like Steve used since space is not a big issue. I also used a T68-6 toroid instead of the T50-2 Steve used.

When I mounted it in a plastic box the sensitivity seemed to increase. I have not put a LED SWR bridge in the box yet, as I was waiting to see how it worked before adding more variables. Today I was able to put an AIM 4170 analyzer on it and it did tune the antenna… seems that the air variable I used is perhaps a tad small. It is almost fully meshed on 40m cw and on 20m it acts like even at minimum capacitance the sweet spot is very narrow and hard to tune.

Here's the innards

My question(s) are:
1) Is the hand/body capacitance normal? If not, what might cause it to
be so touchy?
2) Would my parts layout be part of the issue?
3) Does the DPDT switch (mini toggle) I added for later use with the SWR
bridge add significant capacitance to the circuit? I was able to match a
21Mhz load on the raw test setup, but not once it is in the box.
4) I have a small bus wire for a ground, do I need to increase that?
5) Is the plastic box the problem? Would it be better in a metal enclosure?
6) Am I asking too many questions? Sorry, this is how I learn. Build,
test, ask…

SWR bridge I want to use

Thanks for your wisdom and experience on this one.

72,
Kelly K4UPG

Great that we have some holidays and time off as it allows a bit more opportunity to get on the air. The MI QRP group hosted a 4th of July Sprint and although the hour was late (7-11PM EDT) since I did not have to go to work Monday, I took advantage of the chance to work a few of my fellow QRP ops.

Rain and lightning welcomed my efforts to set up an antenna. So I forsook my normal setup and settled for a twinlead 44 foot doublet hung from my 20 foot Jackite pole which was bungee cord strapped to a ladder in the back yard of our condo. The antenna ran north south so much less than ideal, but at least I could get on the air.

Freshly Built NEScaf saved my bacon!

The day was saved by my freshly built NEScaf filter. As one of the lucky ones, I recently received the latest edition of this great kit provided by the NE QRP bunch. It enabled me to listen to cw despite the high QRN and background hash from neighbor’s TV’s, computers and air conditioners. What a joy it is to actually hear stations through the noise. This is a must have accessory for the condo based QRP op! I am still learning to use it well, but am mega-impressed with the capabilities it offers. With this audio filter, I could null out the QRN and peak the CW signals making for much more relaxed and enjoyable copy. The extra audio boost helps my little Sierra audio too. Keep watching for the next round of kits!