LESSON: A good analyzer makes tuning an antenna fast, simple  and accurate! The AIM 4170 gave us a TON of info (most of it going over my head) and let us see how the C Pole was doing in several areas.  Take a look at this output! (Click on the image for a larger version)

K4UPG C Pole Scan Results

LESSON: I followed Niel’s directions, but did not have a small plastic coffee container so used a Quart Coke bottle instead. So I call it a Coke Choke and it seems to work well. Here’s a photo to show it off!

Coke Choke Ready for Duty

I think this one is a keeper. Goes up easily, hears well and loads nicely too. I made a few brief contacts and called it a day, but look forward to more C Pole action in the days ahead.

72,

Kelly K4UPG PB #173

p.s. Don’t forget to vote in the Ideal Ham Radio QTH poll on the blog!

Think for a minute where the propagation, weather and other conditions create the ideal spot to operate.   Then leave your vote in the poll on my blog and write a comment if you’d like to let us know why…

Nice to dream a bit,  isn’t it?

p.s. Sorry and deepest apologies to the great state of Arizona… must be AZ Brain Freeze at work, it is on the bottom of the list until I figure out how to move it up higher in the software.

72,

Kelly K4UPG PB #173

Orlando, FL btw

Some time ago I purchased a Deluxe Tuner kit from Dan’s Small Parts and Kits aka a QRP Mini Tuner by Mark L. Meyer as described in a 73 magazine article. It is a nice little set of parts and a schematic for the price.

QRP Mini Tuner Kit

So I’m thinking this holiday might be the time to build that little T tuner out and see if I can load up the downspout that runs down the side of my back porch. I’ll let you know how it works!

Hope the bands hold up. Tonight’s QRP-L has a message from N4QA about how nice 40m is sounding right now! Sure would be fun to have our bands back from the QRN and low sunspot streak of late!

Doggone noise and weak band conditions ruined the day so I decided to experiment with the new C Pole antenna that  Neil W0VLZ had suggested. To get rid of a hunk of fiberglass gel inside the barrel of one of the Black Widow Crappie poles I used my cheapo Harbor Freight rotary tool which is a lame imitation of a Dremel tool but gets the job done. A few minutes of fitting and I was good to go.

I’m pretty impressed with it though conditions did not allow for any QSO’s yet. I cut the wire a bit longer than Niel’s directions but it tuned up 1:1 at 13.889 on my MFJ 207 Analyzer. At 14.060 it was a bit over 1.4:1 which is plenty usable. Next time out I’ll do a bit of trimming and be right on the money! Compared to the EFHW in a 20 ft L configuration, it did seem a bit noisier but with condx so difficult it would be hard to tell without some instrumentation.

LESSON: The C Pole is a pretty fine design. I need to work on the physical setup to improve the way the antenna hangs. The crappie poles I used were a bit too flimsy on the top section and leaned inward from the weight of the wire. A better tippy top support system is needed.

LESSON: Niel’s C Pole base design and specs worked very well.  Lacking an empty plastic coffee can, I used a quart diet soda bottle of the same dimension and it worked very well for the balun section. With winds of approximately 15 mph and gusts to 20+ the antenna was stable and I did not use the spikes for the outriggers that I had prepared. Great work Niel. The weight of the base makes it a good choice for backyard or campground use.

LESSON: The C Pole would be a fantastic portable antenna sans the earth side supports. Chuck Carpenter W5USJ has posted a picture of this configuration. Take a look. One point hanger  and spreaders at the top and bottom and simple stake to the ground for anchoring it and you are good to go. I will be testing this next time out by the lake. Winner!

LESSON: The off center fed dipole folded like this and deployed vertically is a good compact option for antenna restricted hams. I bit more work on the frame and support system may pay good dividends in stability and efficiency.

Hope to fly this new antenna in its tree configuration this weekend. I’ll update my results then.

72,

Kelly K4UPG PB #173

Memory Lane...The First Rig

Sure been disappointing lately… the bands are noisy, the thunderstorms consistent and sometimes it seems like no one else is on the air. What happened to my Florida ham radio paradise dream?

Are the bands working elsewhere? Boy, we have had some poor conditions lately. How about you?

On  a high note (pun intended) it was pretty cool to watch QRPSPOTS.COM yesterday as lots of hams helped give signal reports to the Iowa High Altitude Balloon launched by W0OTM team! Congrats on creating some excitement and interesting reports. Now, if I can just get my antenna up to 30,000 feet or more, maybe my FL QTH will be ham radio paradise after all.

72,

Kelly K4UPG PB #173

Our monthly Polar Bear QRP Club outing was last weekend, and I hustled to put together a new C Pole antenna using Niel W0VLZ’s description. After gathering all the parts I set about preparing them. With the 100F temperatures and high humidity, that was a chore since I don’t have a garage with my condo and use my back porch as the workshop. I also have a less than full set of tools and to trim the 3/4 inch PVC pipe to fit the bases of the 16.5 ft Black Widow Crappie poles I had to resort to my Buck knife.

LESSON: Plan ahead and borrow the tools I need!!! YIKES.

I was a bit surprised how heavy the treated 1×4 lumber was. It certainly is not an antenna that is well suited to portable ops where it has to be carried very far.

LESSON: Think about how something is to be used BEFORE using it!

Got the C pole components loaded into the car and transported to the nearby lakeside park in our development. It is a nice quiet spot with towering pine trees and without too many curious visitors, so its a nice QRP portable site. Got my new Coleman shelter set up and went to work on the C Pole. Oops… another lesson. In preparing the PVC to fit into the crappie poles, I only tested the two pvc poles fit into ONE of the two crappie poles. After lugging the framework, antenna wire, coax, balun,  and poles about 100 yds to my site, I discovered crappie pole #2 had a big drop of fiberglass inside the open end of the pole and the PVC would not fit at all.

K4UPG Polar Bear Site Aug 2010

C Pole Aborted Setup by Ninja wannabe K4UPG

LESSON: Check ALL the parts and do a trial setup BEFORE lugging the stuff across the wet grass and wasting time attempting to set it up.

LESSON: Don’t use a new antenna for the first time when the goal is get on the air and have fun!

For the Polar Bears, it was a frustrating weekend for most of us. Propagation was spotty and noise level was as high as the heat. At least I did reconnect with my antenna lovin’ PB friend Aaron, N9SKN/2 working from his hotel parking lot in NJ and had a couple nice ragchews including Julio NP3CW who was 599 and despite two guys calling CQ on top of us was able to be copied well. Great QRP signal Julio.

As you can see, I went ninja and tied a piece of old tee shirt around my head as a sweatband. Actually I was emulating our Alpha Bear, Ron WB3AAL after I read of his early Appalachian Trail exploits and saw a photo of him in his youth and ninja radio mode. Well I tied it TOO TIGHT and left it on TOO LONG and came home with a painful big red stripe on my forehead that lasted for several hours and hurt like all git out.

Ouch Head for the Web... Don't try this at home! Grrrrrrr!

LESSON: Baby Polar Bears should not try to be like the Alpha Bear and wear an unapproved homebrew sweatband. These can be hazardous to one’s health and well being. Don’t try this at home kids!

Beef n Pepper Jack Cheese Wrap K4UPG style

p. s. For our Summer Picnic Events, we are supposed to send a picture of our sammich that we have for lunch. So here is mine!

Until next time…

72,

Kelly K4UPG Polar Bear #173

Grrrrr! The Polar Bears Are On The Loose!

This should be a good weekend for QRP portable. The Polar Bear QRP Group will be out for another Polar Bear Summer Picnic Event and Polar Bears from Spain to the West Coast of the US will be out looking for BSO’s. Grrrrr! I am PB #173 and we’re over 200 members now. With the new Twitter and APRS connections to QRPSPOTS.COM which also point to the excellent spotting site of K3UK with a section for FISTS/QRP Ops to spot and sked one another, there are plenty of ways to use technology to help find each other. Add in a few other contests and state QSO parties, and there should be some buzzing going on this weekend. Makes me wonder when the FOBB results will be announced! Buzzzz Buzzzzz

I’ll be out and if all goes well I will be field testing a new C Pole antenna based on the suggestion I received from Neil W0LVZ. I added some switchable capacitance to my BLT+ and have rewound the main toroid to see if I can push the range a bit more with it so will have a delta loop and probably my W3EDP in the air too. I love playing with antennas and am still amazed when the ones I build actually make contacts!

Give a listen for me on the QRP watering holes on 40m, 30m and 20m Saturday morning. I’ll be self spotting on QRPSPOTS and the K3UK sites to make it easier for you to find me. Let me know how my newest antenna is workin’.

72,

Kelly K4UPG

PB #173

This morning as I took my daily walk around the lake, I met our condo association president. He graciously is allowing me to sink a pipe that will serve as a base to set up my Jackite poles in the backyard. I will be able to pop a cap on the top and keep the dirt and water out and just slide my fiberglass poles into the mount and be on the air in no time. YAHOO… that is a pretty good solution for now.

C Pole Antenna by W0VLZ

But being the antenna tweak that I am, I continue to look for the best alternatives I can find. I’ve started to put together the parts for the C Pole antenna that Niel W0VLZ pointed out to me. He has a fine site with lots of good QRP info too.

So, do you have another idea that can top that one? Or maybe you have a thought for what kind of vertical setup I might use with the new mount?

I’m standing by for my next project assignment.

72,

Kelly K4UPG

Here’s the layout I have to work with at the QTH…

The front yard view... I am next door down from the blue car

Preferred antenna site is the backyard

The buildings run north and south and these photos are shot facing due north. My condo is ground floor, second from the south end of the building. Yes, that is a big electrical transformer box and a major underground feeder line runs to it from the north.

I’ve used my Buddistick with some success but it doesn’t like being so close to the buildings and the swr is higher than when it is out in the open. I also have run a doublet inverted vee fed with twinlead but the north south orientation is not very favorable from my Florida QTH and sends most of my rf into the two buildings. My W3EDP works fairly well as an inverted L with my 20′ Jackite pole and I’ve used end fed halfwaves as slopers and inverted vees but again the directivity is not favorably oriented. I have a 3 foot magnetic loop propped against the wall but it is not working as well as I’d like yet. (i.e. the outdoor antennas work LOTS better so far)

Thought I’d ask ya’ll for some input.

Any outrageous ideas or thoughts for  me? Send me a comment and let me know.

Thanks in advance for your thoughts.

I still think the tin foil does the magic!

After years of neglect, this analog era ham is willing to admit I only understand a bit about digital electronics. (Yep! Pun intended.) Well into the second week of my sabbatical leave, I have begun to plot out a course of study to get up to speed on the state of the art that I have so long neglected. Should be fun. There seems to be a good bit of open source help online these days and I have my trusty ARRL Handbook, Extra Class study guide, Antenna Handbook and assortment of other aids.

Any suggestions from the veteran techies out there will be greatly appreciated.

I am a learn by doing/hands-on sort of guy and find deep theory puts me into a semi-catatonic state after a few minutes.  For me, it’s a whole lot more fun to take a stab at things and find out if they smoke, and it also makes a lot more sense when I can dink and tweak and see what that actually does. But since that is a bit expensive, perhaps I should learn how to use software like spice to do simulations? Any recommendations for how to learn this software?

Another area of toe dipping will be learning to do antenna modeling. For years I’ve looked at those charts and made little sense out of them. HA… I like to throw wire out and see what happens, but in the summer heat, maybe it is wiser to do a bit of modeling from my air conditioned den?

Thanks WX7S-- Your site looks AWESOME for learning this stuff!

I’ll try to share some of the learning curve, but would love to hear from some of you that have gone before. Shortcuts are nice. WX7S your site looks like a great place for me to start! Thanks for the effort it takes to do that.

This weekend (Sat 14 Aug 2010) the Central Florida QRP Group will gather for breakfast at 0730 (Denny’s in Sanford, FL) and off to Sylvan Lake Park in Sanford, FL at 0900 EDT to operate. If you like cw and qrp or are just plain curious… come join us!